Every fishing enthusiast should be able to tiemost common fishing knots, because without them fishing is necessary. This article will tell you how to make a loop on a fishing line using various, most applied and effective methods.
The main advantages of knots for the loop on the lineconsist in simplicity of performance and reliability. It is quite difficult to perform a really high-quality assembly for a beginner angler, because this work requires a lot of patience and practice.
Knitting Tips
- For maximum strength, the nodes need to be pre-wetted.
- It is necessary to tighten slowly so that the fishing line is not heated.
- It is better not to glue the knots on the mono-shaft, after that they become fragile; You also need to consider that for sizing on the braid requires a special adhesive glue.
- If the knot is tied poorly, then it is better to redo it. Good mating has no gaps.
- To insure yourself against surprises, it is better to tie knots at home, previously. The quality of the knot may depend not only on the skill of the angler, but also on the fishing line (on the manufacturer, on its quality).
How to make a loop on a fishing line for a leash
Properly tying a loop on a fishing line for a leash is necessary in the following sequence:
1. A loop is made on the main line, which sticks with a finger where there will be a branch for a leash.
2. After that, you need to take the fishing line after the other end of the loop and make a few turns on the fishing line area (7-9 turns). The result is a rather large loop.
3. Next, this loop folds in half. On the side where the line was doubled, it needs to be divided again.
4. Next, in the middle of a single line, a loop is made, and a double line is passed through it. At the same time with the other hand you need to grab a new loop.
5. After that, the line is wetted and tightened. Here it is important not to tighten the knot too much - when applied, it will drag on as it should.
How to tie a loop at the end of the line
To quickly and firmly make a loop at the endfishing line, you need to learn how to knit a special surgical loop, which has worked well in the fishing industry. Such a loop looks like a "running" knot and is tied not too difficult.
How to make a surgical loop on a fishing line:
1. An open loop is formed at the end of the line. For her tied a regular knot. Then the loop is pulled along the same path again.
2. After that, it is tightened to the desired size (before that, it must be moistened with water).
3. It only remains to trim the excess ends of the fishing line.
How to make a loop on the main line
Such a loop is needed to attach a leash to it. It is tied up as follows:
1. To measure and notice the desired length, you can use a triple knot, which will act as a limiter. After that, the leashes are adapted to the fishing line.
2. To the node-limiter you need to add another, double node, which is not tightened to the end. Thus, out of a double knot is a figure eight.
3. The end of the leash is threaded into the resulting eight: first in one ring, then in another. After this loop is tightened.
On Fluorocarbon Fishing Line
In this section, we will look at how to make a loop on a fluorocarbon line. For it is better to use a special type of nodes, made as follows:
1. The end of the line is folded in half. In length, it should be about 10 cm.
2. This end is pulled in the eye of the swivel.
3. After that, it folds to the main line. The total resulting length should be no more than 5 cm.
4. As a result, the node is wetted and tightened.
Tying a loop on a line of eight
The knot by the eight is often used in fishing business as it is rather simple to execute it and it connects a scaffold very strongly.
How to make a loop on the line eight? To do this, follow the instructions below:
1. The line must be folded doubly and make a medium-sized working loop.
2. Thread the crochet hook into it and catch a small loop with it.
3. Thread it into the big one and remove the hook.
4. After that, hook another loop (respectively, points 2 and 3).
5. Tighten wetted fishing line, and the loop of eight is ready.
Sliding loop on the line
Sliding done specifically to easily regulate the ring. How to make a loop on a fishing line:
1. Throw a fishing line on your index finger.
2. Crochet a hook to hook the line from right to left, then turn the hook.
3. Now it remains only to stretch the loop.
Thus, we have considered the basic ways of how to make a loop on a fishing line.
Today there are a huge number of loops andnodes used by experienced fishermen. For a beginner, to learn at least the basic ones, you need to train a lot. Knitting loops is a laborious and laborious process. Without training is not enough. But do not forget that the more experienced fishermen can always come to the aid of a newbie in knitting loops.
