/ Trimmer outboard motors. Self-made outboard motors

Trimmer outboard motors. Self-made outboard motors

If you wish, you can make the boat motor yourself.from any trimmer. However, it is important to consider that models are available with various component devices. Some trimmers use a long stand, and it will not be suitable for an outboard motor.

Also the problem lies in finding a qualityscrew. It can be placed in a horizontal or vertical position. In order to understand this issue in more detail, it is necessary to consider specific modifications.

homemade boat motors

Devices with double-sided flywheel

Переделка триммера в лодочный мотор с A two-way flywheel is pretty simple. Screw for this should be selected small diameter. Trimmer fits with manual adjuster and low power. Begin assembly with fixing the rack.

If we talk about a simple model, the starter does notneed to touch. When assembling a deadwood, it is important to pay attention to fixing the connector. The screw is mounted on the rack last. Flywheel for the purpose of changing the position of the pipe is attached to the starter. To control these motors is very simple. That water did not get on the connector, various casings are used.

trimming trimmer in outboard motor

Two-stroke models

Make boat motors from the two-stroke trimmerengine can be short or long stance. As a tiller fit a regular tube. It is recommended to start the assembly by fixing the connector. At this stage it is necessary to cut a special plate. For the purpose of its installation, some use metal corners. At the next stage, the starter is mounted. In this case, the spring should not be in contact with the gearbox housing.

The trimmer knob must be protected fromwater ingress. For some, the problem is precisely with fixing the rack. So that it does not hang out, the tube is attached. It should be located at the top of the structure. In order to fix it, you will need a welding machine. At the last stage of assembly, a screw is attached to the rack.

Devices with four-stroke engines

Собираются лодочные моторы из триммера довольно simply. Some prefer not to use the body of the power tool. Experts recommend to build to take the frame of another outboard motor. First of all it will solve the problem with fixing the rack. It is also important to note that the model will be protected from water.

If we consider the classic version, thenassembly takes the connector and is mounted behind the stator. Sometimes racks are used without fixing pipes. In this case, consider the dimensions of the tiller. Some experts use water pumps. In order to fix them, metal corners are installed above the decks. The screws are mounted on a vertical delivery at the bottom of the rack.

do the boat motor yourself

Modifications on the manual starter

Make boat motors from trimmer on manualStarter is the easiest. The connector in this situation is fixed immediately behind the tiller. Before assembly, it is important to make a stand for deadwood. Next, you should choose the screws for the motor. Many experts recommend choosing such items of small diameter.

For the purpose of fixing the connector, it is more expedientuse metal corners. The control lever can always be made from a conventional pipe. At the final stage of assembly, the screw is checked, as well as the tiller. In this case, you need to pay attention to the drive shaft. It should rotate freely, not hang out.

Model with a protected gear

With protected gearbox outboard motor fromTrimmer (drawings shown below) is common. First of all it is important to note that the assembly will require a tight casing. Before starting work, a rack is selected. Also need to pay attention to deadwood.

For regular trimmer, it is selected withoutpushers. In order to install the rack, protective plates are used. A support pipe is used at the top of the structure. To keep the tiller free to rotate, a small hole is made in the motor housing. Some experts still recommend soldering clamps. All this is necessary in order to easily install the motor on the boat.

trimmer outboard motors

Devices with an anti-cavitational plate

Anti-cavitation trimmer outboard motorsslabs are rare. However, in the presence of large racks they can greatly help. First of all, such devices remove the load from the support. It is also important to bear in mind that the deadwood at the motor wears less. Some professionals use water pumps when assembling. If you are interested in low power trimmers, they will not be required. Screws are used with a diameter of 15 cm. In some cases, the rack is fixed on a narrow platform.

trimmer outboard motor drawings

Chainsaw model

You can assemble a model from chainsaw, if availableThere is ready deadwood. Also, the model will need a good rack. To make it yourself from a pipe is quite difficult. Screws are most often used in small sizes. However, in this case, much depends on the power of the chainsaw. Directly clamp is fixed for the starter. In order to protect the device from water, a casing is used.

For fixing the rack used a long stock.Solder it should be in a vertical position. Homemade boat motors from chainsaws with water pumps in our time are rare. It is also important to note that the clamp must be fixed together with metal corners. Some use screws or clips for this.

Motor with regulator

Trimmer outboard motors with regulatorsmeet infrequently. To build a model, you need a quality connector. The starter is most often used manual type. The lever for changing the position of the rack is used a small length. Some install it to the clamp. It is important to carefully clean the drive shaft before mounting.

You should also pay attention to the bottom rack, towhich will be fastened screws. Modifications with protected pushers are not considered in this case. Deadwood should be used without a camshaft. Before installing the flywheel connector is checked, as well as the starter.

Model with retainer lock

Самодельные лодочные моторы встречаются только с spring The connector is used with a one-way flywheel. Some starter experts advise installing a manual type. An ordinary tube is used to adjust the device. The clamp is used a small height. For its fastening fit two metal corners.

Under the connector is attached exhaust valve.Next, it is important to do fixer. Some experts cut a non-metallic plate for this. It should be welded at the base of the crater. However, the drive shaft must rotate freely. To avoid the occurrence of short circuits, deadwood with a protection system is used.

homemade outboard chainsaw motors

Devices with a wide pallet

Self-made boat engines with wide palletsare rare. It is caused by the fact that the clamps for their assembly require very high. As a result, the model weighs a lot. Trimmers, as a rule, are selected small power. For self-assembly of the motor are used conventional deadwood. Connectors are installed with manual starters.

If the trimmer stand is very long, it shouldshorten At the end of the rack for the screw plate is welded. Pushers in this case must be located at the base of the pallet. However, they should not come into contact with the clamp. In this case, the screws need to be fixed with a protective cover. Also, many experts recommend the use of springs to reduce wear of the impeller.