Metal and polyvinyl chloride siding inThe process of facing is fixed to the system of the crate by self-tapping screws or nails along the entire length every 40 centimeters. In this case, the fastening occurs to each intersecting profile of the frame system. However, for the edging of this finishing material and docking along the length, you should use special profiles for siding, or, as they are also called, slats. For each specific case, their sizes and specific configuration of these elements are provided.
Initial profile
If you are thinking about how to set up a profileunder siding, then first you need to understand the variety of these elements of the cladding system. Among others, you can distinguish the starting or the initial profile, which should be located below the trolley, if it is a question of horizontal installation of panels. If the installation is done vertically, then the bar must be on the side where the surface finish begins, namely from the pediment, the wall or the eaves. Thus, this element will be on the right or on the left.
If you are faced with the question of how to exposeprofile under the siding, it is important to remember that, unlike the panel, the installation of the described system elements is carried out as rigidly as possible. Fasteners, namely self-tapping screws or nails, should press the bar as tightly as possible. Elements of the lath are hooks for the panel. The initial bar has a length that is typically 3.66 millimeters. When facing the construction, the color of the starting profile will not make any difference, as it will later be hidden by the trim panel. If we take into account the fact that this is a rather thin profile, the technology involves screwing not onto individual racks of the dumping system, but onto the plane.
If you decide to choose a proprietary subsystemventilated facade that serves as a frame for cladding, then there is a horizontal profile, whereas in self-made structures a UD profile is added, but in the wooden crate there is a perforated corner.
Setting of the angular profile
Before exposing the profile under the siding,It should be taken into account that this system assumes many elements, including angular profiles. They are used to decorate the outer corners and to join the panels together. To install these slats independently carrying the extreme rails of the shed system must be mounted in steps of 10 centimeters from the corner of the building. It is important to pay special attention to the perforated mounting edge of this profile, which lies on a plane located at the same distance from the corner.
Before starting work, you need to decide which profileunder siding choose. It must necessarily be made of the same material as the panels. The profiles described above need not necessarily have a smooth surface, they can repeat the decoration ornament. Thus, in the collections of the socle siding, the profiles are made with an imitation of a brick or natural stone, namely the pattern that this batch possesses. Despite the fact that the corner bar with the imitation of bricks can be used for siding, which looks like a natural stone, in the end everything will depend on the designer's decision.
The distance between the profiles under the siding, asThe rule is determined by the width of the finish. For any kind of panels, the profiling of the connection bars will be the same. Thus, the profile under the log will be the same as under the "shipboard". It is necessary to take into account that the finish with the heating expands, therefore, making the fixing in the profile, you should reduce the length by 10 millimeters. This will eliminate the inflation at the stop, which can cause deformation of the profile and the surface itself.
How to expose an angular profile
If you are wondering about how to exposeprofile under the siding, it should also be taken into account the fact that in the buildings, in addition to the outer corners, there may be internal ones. For them, you should use a guide that has a similar value. The master should remember that in the absence of it for finishing the internal profile, you can use a pair of J-trim-strips, which are mounted on separate planes. To fix the internal angular profile, it is necessary to make a 10-centimeter indentation of the carrier elements of the wire from the corner, then the fastening part of the strip will coincide with the frame. The profiled inner angle bar has the same length as the outer one, this figure is equal to 3.05 meters.
We expose the J-TRIM profile
Learn how to mount the profile under the siding, youyou can after reading this article. There is another element that is used in the interior corners in the process of facing the buildings. He was mentioned above. This profile is intended for those cases where only one wall is faced. This element is called edging or ending. In some cases, it is used in place of the edging, it is used instead of the finish or starting line.
Such a profile can be observed during the finishing processeaves siding. The length of the guide in the usual version is 3.66 meters. The technology of the installation remains the same: you will also have to provide a rigid fixation with the help of nails and screws, which are installed in steps of 40 centimeters.
Setting the finish profile
If you do not know how to mount the profile undersiding, it is possible to familiarize with one more technology of installation of a finishing strip. Its configurations resemble the above-described profile, but this element differs less impressive thickness. It is assigned to keep the finish not in the profile thickness, but in the thickness of PVC.
The finishing strip is able to tightenthe final panel, but this will not be enough to hold the element, as a strong gust of wind can inadvertently tear the canvas off the seat. In order to exclude such consequences, the finish, refueled in the finish profile, should be additionally reinforced with screws through the lining. It should be noted that the fasteners must be made of stainless steel.
H-profile installation
When a frame is created for siding from a profile,there is a need to install this element. This is necessary for the reason that the wall of construction is most often longer than the panel. It is for their connection that this profile is used. Carrying elements of the trolley are located vertically, and in the same direction it is necessary to set this bar.
For fixation between vertical profilesThe frame system should be strengthened horizontally, observing a step of 50 centimeters. They will be the basis for the installation of the above-mentioned bar. The fixation of this profile is made using the same technology used to fix the remaining elements.
Features of the installation of the window profile
When framing a frame for sidingprofile, there is necessarily a need for using okolokonnyh elements. They are used to close the slopes. These components of the system are like the letter F. The wide part covers the escarpment, but if it turns out to be too large, it can be cut with a construction knife or angle grinder using a ruler.
Fixing of this profile is made for perforated edge by screws or nails, which should be removed from each other by 40 centimeters.
Tips of the master
How to expose the corners from the profile under the siding, it wasdescribed above, as well as the technology of installing the remaining profile elements. The main profiles that are used for the facing of the building are considered in the article, but on the market you can find auxiliary slats, the price of which can be very different. For vinyl finishing, use only the vinyl profile. Galvanized steel can only be used for metal panels.
If you are thinking about how to properly exposeprofile under the siding, it should be noted that when installing the finish on the building, it is necessary first to fix all available profiles. Only after this is allowed to start the installation of panels. Experts recommend using items that belong to the same collection. First, you need to decide which - vinyl or metal - profile under the siding to choose. Each type of material has its own positive and negative features. Metal has a longer service life, but the vinyl profile does not exert pressure on the walls and foundation.
Conclusion
It is important to withstand the distancebetween profiles under siding. Recommendations on the technology were presented above. If they are available for your understanding, then the installation of the panels themselves will not be accompanied by special difficulties.
