Every mobile device, whether it's a smartphone ortablet, today has a large touch screen. You can control this gadget, of course, only by touching it on that screen. And this, in turn, causes pollution of an ideally clean display surface, the emergence of cloudy spots, flaky tracks and so on. And this is not to mention the banal possibility of polluting the display due to external factors.
The only solution that can help allus in working with devices, this is a protective accessory - a film. We are going to tell you how to correctly apply the film to the phone and the tablet in this article.
Why glue the film?
In addition to the fact that it providesprotection of the screen from dirt, dust and fingerprints, there is also a function to protect the display device from mechanical damage. And this, believe me, is much more serious.
After all, in real life it is impossible to provide100 percent ideal conditions for the operation of the phone or tablet - there can always be a situation where an item touching the screen will leave a scratch or scrub. Obviously, the appearance of the gadget will suffer from this, not to mention the performance (and image transfer).
If you know how to properly apply protectivefilm on the phone, and do it in a timely manner, worry about your device is not worth it. You simply remove the old film in the event that its appearance ceases to suit you, and replace it with a new one. Thus, the screen itself of the tablet or smartphone will remain unharmed.
Without a film, it is obviously possible to get rid of the scratches that appear after the screen has been replaced.
How are the films arranged?
Having understood the use of a protective film, it is necessary to drawattention to the way it is arranged. So, if you take one such film in hand, you will see that it has two labels. On the first one it can be indicated that this is the protective layer number one; on the second, respectively, "layer number 2".
All true - modern films are delivered onmarket three-layer. If you imagine them in the form of a sandwich with two slices of bread and sausage inside, then the actual "film" (sausage) is the real film that will protect your screen. The last layer - "bread" - will be removed during the installation process. They serve to protect the film itself from damage (both from the top and from the bottom side). If you want to know how to properly apply the film to your phone, remember to remove them.
Preparing the screen
A pledge that the film will reliably hold inDuring the use of the device, it is not only its condition and quality. In fact, an important role here also plays a surface on which the film will be glued. In this case, we mean the screen of a phone or tablet.
In order for the film to stick, from the surfacedisplay you need to remove all unnecessary: dust, mote, fingerprints, moisture. If anything remains, in the future the appearance of the gadget's screen will be a bit messed up.
Again, if you want to know how to correctlyTo stick a film on phone "iPhone 3G" (as well as on any other model), do not forget to clean the display. You can do this with a soft napkin or cloth, which does not leave villi.
It's simple:rub the screen and look at it at an angle to determine if anything is left on it or not. Ideally, the display surface should look smooth and smooth. Then, after the protective layer of the film has been glued, the screen will look great.
First step
So, after cleaning the display first thingIt is necessary to try the edges of the film to the border of the screen itself. According to the instructions on how to correctly apply the film to the phone "Fly 4403" (and not only to it), the gap between it and the border of the display should be approximately 0.5 millimeters.
This does not mean that you need to equip yourself with a ruler andmeasure the same distance - no. You just need to "eyeball" to estimate that from the film remained a small gap. This is normal, because the films produce in slightly smaller sizes than the screen, so that they lie more evenly.
After you have outlined the "beginning" - the line from which you will glue the film, it is necessary to proceed to its further gluing. You need to do this gradually, slowly. However, read more about this.
We put the film on the device
As you already understood, if you do not know how to correctlystick the film on the phone, start with a clear line, after moving gradually to the opposite edge of the device. As experts say, you need to act on the narrower side of your gadget. So it will be easier to glue the film with an even "front".
Next, you need to use tools forleveling the surface of the already glued layer of material. In particular, it is a plastic card (although a scraper will do). Pressing it to the surface of the display, covered with a film, you can "drive out" the air bubbles arising there. Thus, the screen will look nice and neat.
Remove the top layer
After you managed to cover the screendevice film, go to the next steps, namely - remove its upper protective layer. This is done simply: you need to pull the label left on the film, which says "Layer number 2" or "Remove after gluing" (depending on the type of film). Do this gradually and carefully.
If you have learned how to glueprotective film on the phone (Gerffins it or any other brand), after removing the top film you should have a perfectly smooth coating protecting the display device. Actually, after that you can start using your gadget.
Possible problems
Anxiety can arise ifyou though read, how correctly to stick a film on phone, but have not made all properly. For example, this applies to uneven gluing of the film or air bubbles remaining on the screen.
In the first case, you can simply re-paste your film. It takes a little time, and if you do it right, the accessory itself does not go bad, it can be used again.
Another problem is the bubbles that will makeyour screen is ugly. You can deal with them in several ways. The first one we already described earlier - arm yourself with a scraper or plastic card and just "squeeze" them to the nearest edge of the device. This will help to overcome the big bubbles. As for the small ones, most of them, as practice shows, can disappear themselves. So do not be discouraged if you notice a couple of them. The main thing is that they should not be caused by any mote falling between the glass and the film.
The place where to glue the film
In addition to recommendations on how to correctly apply the film to the phone (photo - also a visual material), I would also like to give advice on the place suitable for gluing.
As mentioned above, it is necessary to excludethe possibility of getting dirt, dust, hairs and other objects on the glass of the device. This means that it is not possible to film the film qualitatively in dirty, dusty rooms normally. The same applies to open space - the wind can spoil everything.
We recommend choosing a room where it is clean and windless. If we talk about an ordinary apartment, then the best for these purposes is a bathroom, for example. Because of the high humidity of the dust there is less.
Go to such a room and pour your film. Let's hope you succeed!
