How to create a restore point in Windows 7? Creating a Windows 7 Restore Point

Let's look at how to create a point in Windows 7recovery. You should also figure out how to disable the corresponding mode. With this approach, in the event of an emergency, you can return to the previously specified settings.

How to create a restore point and restore system in Windows 7

Let's start by clarifying what constitutesSystem Restore. This is a function that allows you to make a restore point of Windows 7. When recovery is active, in automatic mode, before installing drivers or programs, as well as after a set period of time, a copy of the most important system materials and settings is created on the computer.

Note that create a Windows restore point7 you can manually. How to do this, further discuss in more detail. You may have a question - why is the creation of a Windows 7 recovery point going on? It should be noted that this is a very useful function. If there is a certain problem in the process of booting the computer, you can do a full or partial rollback of the system.

In other words, you can restore system files using Windows 7 checkpoint recovery, created, for example, a couple of days ago, at a time when the computer worked fine.

This solution will save your time, and in some cases it may even save money. We recommend that you enable the recovery function and, if necessary, manually create points.

How to create a restore point and activate the process in Windows 7

First, let's check the settings, ratherall, initially you have all the necessary features included. Right-click on “Computer” and select “Properties.” Next, on the right, use the “Additional system parameters”, and then in the resulting window, go to the “System protection” tab.

If in the protection settings opposite one(at a minimum) the local drive is “Enabled”, then the system recovery feature is enabled, and a Windows 7 recovery point will be created. However, if “Disabled” is written everywhere, the above function must be enabled. For this purpose, select one of the listed local disks, and then click the "Configure" button.

You can, for example, select a section in whichyou the most memory. A window will open, and in it you need to point to "Restore system settings." Further below, use the slider to specify the maximum amount of hard disk space you want to allocate to create recovery points. During the creation of new points the old ones will be deleted. Click "Apply". After that, the system will tell you that recovery is enabled. This means that if a problem occurs with a personal computer, you will be able to restore Windows, even if the system does not boot.

Disable System Restore

In case you want to disable recoverysystem, it can be done without much difficulty. Specify the local disk with recovery enabled and click "Customize". Note that the system restore point Windows 7 can also disappear according to your desire.

In the window that opens, simply installtag near the item that disables system protection, and then click "Apply". You will see a special warning, you should click the "Yes" button in it. Thus, system recovery will be disabled.

Create a restore point manually

Remember to create a restore pointIt should be before installing certain programs or before making significant changes to the settings. If for some reason you are not sure that your actions are “harmless”, it is better to create a restore point so that you can return the system parameters to their original position.

To manually create a point, you need an activesystem recovery status You need to go to the properties of the system, switch to the tab called "System Protection". Click the "Create" button. Next, enter the name of the recovery point. You should wait a bit for the system to complete the setup. Click the "Close" button. That's all ready, you can safely install a new driver or program.

System Restore "Eighth Version"

If we talk about the means of recovery of thisoperating system, then first of all it is necessary to make the initial protection setting. Make sure that System Restore is activated for the partition that placed the Windows files (usually “Disk C”). Specify the amount of space that is needed for the operation of "System Protection".

Стоит отметить, что в данной системе появилась the ability to restore using a specially created for this purpose disk or installation CD. You can also restore Windows 8 without deleting user files. At the same time, a special program designed for the specified purpose can be launched directly in the operating system or in the case when Windows 8 refuses to boot.

Recovery Images

We emphasize that by means of the system you cancreate 2 recovery images. The first works with the program "Refresh". If you use this tool, the procedure of full recovery of Windows 8 occurs, personal files will not be touched, but the installed programs will be deleted, and the system settings will be reset to their original ones.

If you decide to create an image using the commandthe lines, “Refresh” will use this image for recovery, and will not need the Windows 8 installation disk. In this case, the system settings and programs you set will not be reset. They will return to the state relevant at the time of the creation of this image.

The image created by this method will not work if you need to perform a recovery with full formatting of the main disk partition or accidental deletion of the system partition.

File recovery

The second method is suitable for creating a completebackup image. This solution involves creating a second image using the tool in the Control Panel, which is called "File Recovery". In this way, you can restore a new Windows system completely to an empty hard disk.

On practice

For example, you create a Windows 8 system image andinterfere with it on the disk (D :), then remove Windows 8 completely from the main disk (C :) to install Windows 7. Using the previous system, you understand that you do not fully like it. Then you can easily restore the original Windows 8, which will include all your programs and files.

All this is possible thanks in advanceprepared image. The new system has changed the ability to enter safe mode. For this now there are many ways. For example, the transition is possible directly from a running operating system. It is also possible if you could not load Windows at all.

Note that the ability to restore previous versions of files that are familiar to the Windows 7 system has been replaced by a special tool called "File History".

Windows 8

Recovery tool is significantly different fromWindows 7 system recovery. First of all, enable system recovery for the partition in which the system is installed. This feature should be enabled by default. The operating system independently creates a restore point in front of significant events for itself.

For example, the specified action will occur before installing the driver or program. Using recovery points can help even if an operating system is infected with a virus.

In the system recovery settings window, selectDrive (C :) or another system drive and click "Customize." Next, you need to mark the item on the inclusion of system protection and specify the parameters for maximum use of space within 15%. This number is enough for the stable operation of the protection function of your system partition containing the installed Windows 8.

Do not forget to click "Apply" and then "OK."You can enable protection for other sections. Periodically, you should create new recovery points yourself. In the appropriate section, click "Create." Come up with a suitable name. Once again, click "Create" - and you're done. To apply the created point, go to “Settings”, select “Control Panel”, then “Restore”, finally, start System Restore by selecting the appropriate function. So we have figured out how to create a restore point in Windows 7, as well as a similar feature in Windows 8.