Recently quite commonequipment with which you can cook shish kebab and any other food. In this case we are talking about the brazier with a stove. It can be built independently, using a brick or steel.
Preparation of tools for a brazier of a furnace from a brick
Among the necessary tools for laying brazier need to highlight:
- Master OK;
- vibrating plate;
- rubber mallet;
- the Bulgarian;
- shovel;
- capacity for solution.
The described equipment providesNecessity of site arrangement. To do this, you will need a ceramic brick, a dry mix for its laying, wild stone, a metal corner, fireclay bricks, as well as roofing material. For the design itself should be prepared:
- cooking stove;
- fire door;
- blew the door.
Preparatory work
Если вы решили возвести мангал с печкой, то для First you need to choose a place to install it. The territory should be open, for this a large yard is perfect. If plantings interfere, some of them can be removed. In the absence of a concrete pad or asphalted area, a foundation must be prepared.
The design will have dimensions equal to 2.5x1.5 m. The platform for it should be 3 m.2. The selected place must be cleared of debris, remove the top layer of soil, and then note the size of the future brazier. To deepen the foundation must be below the line of soil freezing.
Foundation construction
If you decide to build a brick brazier,then it should be installed on the foundation. Concrete solution is perfect for him. When the clay soil is in the area, then after digging out the trench, you can immediately start pouring the foundation with concrete. However, if there is a lot of sand in the ground, then it will be necessary to install formwork, only after that you can start pouring.
В качестве примера будет рассмотрена конструкция, which rises above the ground surface by 1 m or more. The chimney should be raised by 5 m. The average depth of the foundation should be 30 cm. To create the foundation, it is better to use concrete M-200. To prepare the solution should be used:
- 1 part of cement;
- 4.8 pieces of rubble;
- 2.8 parts of sand.
The foundation can be strengthened with a clay castle. For its formation, clay is used, which is laid in a layer of 2 cm around the foundation. The material must be tamped.
Mangal construction
Erecting a brazier with a stove, on the foundation is necessarylay the roofing material in 2 layers for waterproofing. The first two rows are made continuous. In the third row, you should install a steel door, while the fourth row will be solid again. In the next row it is necessary to close the ash door with a lock and install the grate. A 5 mm gap should be left between the grate bars and the bricks.
The sixth row is laid out without a pass.In the seventh row, you can install the fire door. Further it is necessary to lay several rows in clods. With 10 rows, you can begin to form a chimney, while 11 rows will allow you to block the opening of the furnace door. In the 12th row one should create a brazier hearth and an oven stove.
Уровень жаровни будет располагаться с 10 по 13 rows. The next row should be laid out in such a way as to form the side and rear walls of the furnace, as well as the flue duct. For the 23rd row, an arched ceiling is constructed. From 24 to 31 rows, the brick is laid out in solid rows. The transition to the pipe begins with 32 rows. The cap is formed from the same building material as the furnace itself. However, some use metal products.
Brazier stove under the cauldron
Кирпичный мангал с печкой под казан может иметь foundation, arranged by the above technology. However, in this case, the clutch will be somewhat different. From 13 to 17, the laying should be in the form of a letter P. From the second row should begin to form a blow chamber.
In the third row there will be a door.blew. Here you need to leave a space that should temporarily be bricked up On the fifth row you need to form a place for a metal grid. For barbecue grills on the sixth and eighth rows in the walls should be left pins or brackets. They can be mounted in several rows. This will allow you to move products according to your tastes.
On the seventh row is laid chimney channel.The next two rows will allow you to create a place for the cauldron. This hole can be used to install the tank for heating water. A cooktop is installed in rows 12 through 17.
Performance of the brazier-furnace from metal: preparation of a support
Мангал-печка из металла выполняется после production of support, which should be as reliable as possible, because it has to undergo the weight of firewood, a cauldron with water, as well as prepared food. For this purpose, corners and shaped tube are usually used.
The legs are welded to the top cross, theyshould form a rectangle whose dimensions are equal to the length and width of the main part of the structure. The width of the crossbars can be equal to 4 cm. Exactly the same elements are welded to the legs with a distance of 20 cm from the ground. A shelf for firewood should be placed on them.
Manufacturing stove-grill
Oven-brazier, photo of which you can seein the article, quite often made of sheet metal. To do this, take the workpiece with a width equal to the height of the furnace. The strip bends, and its edges are welded together. At the top of the shell can be made triangular slots, which will be holes for firewood.
This design will also be a great stand.under the cast iron cauldron. In each corner in the upper part of the shell it is necessary to make an opening. Its length should be 2 cm. Each petal bends outward, and the edges of the petals bend to the top. This should be done until the cauldron is free to sit on the bezel. It is impossible to bend the petals in the center, because they will burst into the walls of the pot when heated.
Conclusion
Мангал с печкой можно выполнить ещё и из баллона or pipes. These options are the simplest, because the sheet metal does not even have to search and weld. The length of the pipe must be at least twice its diameter. The difficulty in this case can only be to find a suitable product. It should have a sufficiently impressive wall thickness, because otherwise the design will not last for a long time.
