Jacks among motoristsare in great demand. First of all they are distinguished by compactness. It is also important to note that many models are lightweight. On average, a modification with a load capacity of 3 tons has a mass of 13 kg. In the workshops, sliding models are also in demand. In the first place, they are quite quiet. However, in this case, much depends on the manufacturer. Plugs are most often used open type.
Piston systems for models are located inrear end. On the whole, the designs of the roll-on modifications are quite similar, however, there are models with struts. Also modern jacks are equipped with protective supports. More on the market are models that have a wide heel. There is an average jack type podkatnogo type in the region of 3200 rubles.
3 ton rolling jack: what is better to buy?
В первую очередь при выборе домкрата важно pay attention to its parameters. The minimum lifting height of the device must be equal to 130 mm. Heels are most often installed with a width of 4 cm. For a load capacity of 3 tons, this is considered normal. Next, it is important to estimate the maximum lift height. This indicator should not exceed 320 mm. With a length of 28 cm jack must weigh no more than 7 kg. If we talk about design features, then the lifting mechanism is first of all evaluated.
The handle should rotate freely.The upper part of it, as a rule, rubberized. Outlet valves in the device must be protected. Opening models are not advised to choose. Separately, you should consider the connecting plate. The seam on it should be neat and smooth. The spring in many versions is installed in the back. It will cost an average model of a good manufacturer in the region of 3400 rubles.
Modifications with spacer
With 3 tons jack-strut strutuse? Data question certainly worries many. In fact, everything is quite simple. In order to lift any object, the heel of the device should be located under the fulcrum. Further it is necessary to fix the jack with the help of the holder. The next step is to raise the heel of the millet, working the handle of the device.
It should be noted that models with struts in ourtime are pretty much in demand. Their handles may vary greatly in length. Directly spacers are located near the side racks. The protective cover is located at the top. It should also be borne in mind that the devices weigh, compared to conventional models, much more. On average, the mass of the jack is at 13 kg.
Wide heels
Models with wide heels meet prettycomplicated. However, global manufacturers have recently equipped them with their devices. Their distinctive feature can be called increased resistance. It should also be noted that they are available with wide racks. Protective covers in many configurations are installed in the upper part of the case.
Pens exist as rotary, sofixed type. Slips are most often used rubberized. If you believe the opinion of customers, then this type of model is not much in demand. However, for devices with a payload of more than 3 tones, wide heels are more important.
Jacks with protective supports
Jacks with protective stands released inmainly company "Miol". On average, they have beams installed with a length of 33 cm. Outlet valves in almost all versions are located on the rear side of the jack. Handles on length can vary greatly. Almost all modifications with protective supports are made without holders. There is an average jack of this type of area of 3 thousand rubles.
Model "Forte"
Among the models "Forte" rolling jack 3 t whatbetter to choose? Modification "TA-82" is most suitable for workshops. If you believe the opinions of experts, then it has no problems with sustainability. The handle of this model has a fixed type. However, it should be noted that the stabilization of the jack has a good one. He also has great steel wheels. The overlay in the presented sample is rubber.
Bearing stop in the specified configuration is applied0.4 cm thick. Directly holder mounted in the back of the structure. There are two exhaust valves in the model. If we talk about the protective cover, it is located in the upper part. The stub in this case is provided by the manufacturer. Also, this model wheels are used with a special coating. Thus, the jack moves very quietly.
Jacks "Koto"
Considering the model "Koto", rolling jack 3 twhich one is better to choose? The first thing to note is a modification of C02, which is made with a protective stand. If we talk about its parameters, it is important to mention that the minimum lifting height is at 120 mm. The beam itself is set to a length of exactly 33 cm. The heel width of this model is 4.3 cm. The piston modification system has a pressure that can withstand a maximum of 3.2 bar.
If we talk about the pen, then it is in this caseMade with a soft lining. Thus, during the operation of the device the car will never be damaged. If necessary the jack can be put on the holder. In this case, the protective cover is used quite wide. Cap manufacturer is not provided. The wheels of the model are not used large diameter. If you believe consumer reviews, then this jack rolls through a special coating with absolutely no sound. It is worth today the presented model in the region of 3100 rubles.
What are interesting models "T-Max"?
Among the models "T-Max" rolling jack 3 tonswhich one is better to choose? Specifically, modification 103A is capable of boasting a long handle. If necessary, the user can scroll it. Also, this model has a wide heel. According to the documentation for the device, the length of the beam is 34 cm. Directly the piston pressure system is 3 bar. Wheels of this model are steel, and the pad is used polyurethane.
Recoil in this case, the manufacturerprovided for. The cap is applied open type. However, the model still has disadvantages. First of all, it is important to mention the lack of a soft lining on the handle. Thus, the car can be damaged when operating the jack. For workshops, this model is not suitable. It costs about 3400 rubles in stores.
Intertul models
Considering the model "Intertul", rolling jack3 t which one is better to choose? The most popular modification "T0400", which is made with a protective lining. Directly, the heel in the presented configuration has a width of exactly 4.5 cm. In turn, the beam is used in a length of 25.6 cm. There are two side struts on the model. The holders in this case are mounted on brackets.
Колеса установлены небольшого диаметра, they have a polyurethane lining. The lifting mechanism in the jack is located at the rear block. Built-in tray for storing tools in the presented model is missing. Special attention deserves the quality of the handle. If you believe the opinion of buyers, it rotates freely. At the same time it has a rubber lining. In total, the manufacturer provides two graduation clans. The holder in the presented model is mounted near the lifting mechanism. It is in the shops it is not more than 4 thousand rubles.
Jacks "Vitol"
This company mainly manufactures models withwith spacers, however, in its assortment there is also a conventional 3-ton rolling jack. Which type is better to choose? The jack "DV-101" among the competitors is famous for a strong beam. In this case, the side racks are made of steel. The bearing emphasis in the presented configuration is available with a corrugated surface. If you believe the opinion of buyers, the handle is provided for a long and convenient to use it.
Directly holder in the design is available.In this case, only one exhaust valve is installed. The protective casing is standard located in the upper part of the body. The stub of the model is normal. The system against overturning by the manufacturer is provided. Pad under the piston system is used completely rubber. The unit of this model is U-shaped. If we talk about general parameters, then the maximum lifting height is at 140 mm. The price for this rolling jack 3 tons (photo shown below) varies around 3,500 rubles.
Model "Bison"
Considering this rolling jack 3 t,Its description should begin with design features. The device is made with a wide heel, and therefore is in great demand. If you believe the opinion of buyers, the model is equipped with a sturdy frame. The length of the beam in this case is equal to 28.5 cm. The support bearing itself in the presented configuration is applied with a rubberized grip. The handle of this jack has a fixed type.
The model holder is installed, and this isimportant advantage. Also, this model is in demand because of the low landing. The minimum lifting height is at 125 mm. The protective cover in the jack is installed in the upper part of the body. The model has two total racks. Piston system is located at the handle. The tray for storing tools in the presented configuration is missing. The frame in this case is set U-shaped. Front holders are mounted as standard on the brackets. This rolling jack of 3 t Zubr is worth not more than 3,400 rubles.
Capabilities of the Matrix model
This rolling jack 3 t "Matrix" reviewshas good ones. Its peculiarity is the presence of a small handle. It is also important to note that this model is compact. Rubber pad on the handle is missing. If we talk about the parameters of the device, it is important to mention that the minimum lifting height is 122 mm.
Колеса у данного домкрата применяются с polyurethane coating. Dina beams are only 25 cm. The heel of this model is provided with a diameter of 3.5 cm. The plug in this case is of the open type. Special attention deserves the strength of the frame. The thickness of the metal at the base is 0.2 cm. The rolling jack will cost 3 tons "Matrix" to the user about 3200 rubles.
Summarizing
Учитывая все вышесказанное, следует отметить, что for an ordinary motorist is ideal jack "Bison". In use, it is quite simple, and the heel of its manufacturer provides a high-quality. You can still consider the device "Matrix". In the market it is inexpensive, and therefore also in demand.
