When it is cold outside the window, it becomes necessary to heat not only the living quarters, but also the garages, as well as the workshops.
Need to use
If you are a car enthusiast, you are familiar with the fact thatThe battery does not like cold weather. And to start the car will be quite difficult when the temperature outside the garage drops below the maximum possible mark. If you like to do something in the garage, then you are probably faced with the need to use the stove.
As practice shows, the stove on diesel is the most optimal and economical device that you can make yourself.
The use of gas cylinders
Конечно же, в магазинах можно приобрести агрегат, designed for heating small spaces. However, such devices are designed for specific operating conditions. If you manufacture the device of the type described by yourself, then you will be able to count on your needs by making the stove one that will ideally meet the intended operating conditions. It will be not only economical, but also effective.
Often enough for the manufacture of suchThe instruments used gas cylinders that were used for oxygen or carbon. Fuel will flow by gravity, and from the forced supply of oxygen must be abandoned, because the design is not required. In order not to create a fire hazardous situation, it is necessary to exclude the cylinder heating, setting the height of the contour according to the height of the source of combustion.
Preparatory work
If you will produce a stove on diesel,you have to prepare chimney pipes, which should be 4 meters or more long. In this case, the wall thickness should not be more than 2 millimeters. The internal diameter of the pipe should be equal to 10 centimeters. The main element will be a silent cylinder, the volume of which is 50 liters. Its walls should not be more than 1.5 centimeters. The fuel tank should have a volume in the range of 8 to 15 liters, and the pipes for the burner should be made of copper.
You will need a file and grinder, steel angle of 20 cm, welding machine, electrodes, tape measure, level, drill and drill.
Balloon Preparation
If you will be running the stove on diesel,It is important to pay attention to the wall thickness of the product. The principle of operation is that combustible fuel vapors must be formed. If the walls are thicker than the above parameter, then the boiling point will not be reached. It is necessary to drain the condensate from the bottle outside, and then rinse the tank twice to free it from the odorant. After the balloon is poured to the top with water, buried in the ground for stability. In the course of entering the Bulgarian, with which you will need to rid the container from the top of the valve.
When the stove is made on diesel, the firstthe cut will cause the water to decrease. You need to wait until it drains, only after that you can continue to separate the upper part from the bottom. With the help of a welding machine, legs that are made of metal corners should be welded to the bottom of the tank. The cylinder is installed, and then you can proceed to the assembly of the structure. The chimney must be vertical, devoid of slopes and angles. The length of this element should not be less than 4 meters. The design can be poured and mining, but it must be cleaned beforehand. If you use unprepared oil, it may be alcohol and water. When heated, such a mixture can cause a fire or explosion, which is especially critical in a garage.
The manufacture of the furnace on the basis of the drip method
Miracle-stove on diesel can have a dripconstruction This option is considered quite simple and quick to manufacture. To carry out the process, a medical heating pad should be prepared, the volume of which is approximately 2 liters. To the rubber hose, which is provided in the heater, you need to attach a copper tube, which is bent at an angle of 90 degrees. The rubber hose is bent in half, a tin clamp with a screw is installed at the place of the bend. This design will effectively regulate the flow of fuel from the burner, which should drip.
The device is suspended on the wall, for thisYou can use the designated hole. When such a miracle-stove is made on diesel fuel, in the next stage you should prepare a cloth that will act as a wick. Rags are soaked with diesel fuel, and a red brick is placed under the rag into the oven. The furnace itself will be a metal container, for this it is recommended to use 1/2 of the barrel. The door should be small, its size should be sufficient to load fuel. Often homemade craftsmen made a stove on diesel with their own hands. When the door is formed, slots are formed that will play the role of the blower. The pipe should be made of tin and resemble a samovar. Thus, it should consist of several knees.
The hole for the pipe should be positioned as possiblefurther from the door. In the central part of the furnace you need to make a hole that will match the diameter of the tube. If you place this element on the side, and not on top, then you will have the opportunity to get a surface for heating and cooking. Such a stove on diesel fuel, the price of which is 7,000 rubles in stores, can be done by you yourself. The fuel does not need to use wood, and the intensity of combustion, you can adjust as you wish. Among the shortcomings can be identified fire hazard and odors.
Production of the furnace from metal sheets
Most prevalentdevices that are made of steel sheets. This design is compact, and you can use the following dimensions: 70x50x35 centimeters. This is true, except for the chimney. Such a device will weigh only 27 kilograms, with its help you can cook food or connect water heating to it.
Considering the positive features, you can also highlight the fact that the device is not afraid of frost at all.
Preparation of materials and tools
Oven for garage on diesel you can becompleted if you prepare 4 steel 20-centimeter angle, steel sheets, the thickness of which is 6 and 4 millimeters, as well as chimney. You will need a hammer, tape measure, level, file, grinder, welding machine, sheet bending machine and electrodes.
Methods of work
ZAZ stove on diesel you can be purchasedin the store, however you are able to make it yourself. For the tank, the material should be cut with a grinder, and then the workpieces should be joined together by welding. Further, holes are made in the housing for installing the chimney as well as for mounting the door. At the final stage, legs are strengthened for structural stability.
ZAZ stove on diesel is sold in the departmentsgoods, but it is much more expensive than the one you can do yourself. That is why garage owners often resort to this solution.
