As one of the most important stages of repairstands the alignment of the walls and their preparation for the decoration. From this process will depend on the aesthetics of the room, durability and reliability of repair.
If the work you plan to carry outyourself, you need to ask how to dissolve the putty. It is important to know the proportions of the dry composition and liquid, inquire about what methods of mixing are used today, as well as learn about the optimal consistency, which will depend on the purpose of the composition and its purpose.
What should be puttying solution
If you are interested in the question of how to breedputty, then you should know that the mixture for such work should be elastic, plastic and resist smoothing well. It should adhere perfectly to the surface, not run off from it and not fall off in pieces.
It is important to ensure that the composition is well behind.from the spatula and had a homogeneous consistency. The mixture must be stirred so that it does not have solid inclusions and lumps. By purchasing ready putty, you eliminate the need to bring the mixture to the desired consistency. The manufacturer took care of this, the master will only have to mix the putty well. However, the cost of such products is much higher compared with dry analogues, which require preliminary preparation.
If the surface needs to be seriously leveled,You can fill in cracks, hollows and holes with the compound, then you can complete the work in a shorter period of time with the help of putty with a thick consistency. Such a solution will make it quite easy to seal the joints between the plates.
Different consistency for specific purposes.
If you are interested in the question of how to breedputty for finishing walls, it is necessary to prepare the composition in such a way that it has a more liquid consistency, it will be easier to apply a thin layer and make the base smooth.
For ceiling and walls, the proportions of liquid from drythe composition sometimes has to be changed in order to achieve a higher adhesion with the surface. Dilute the putty before use. Each mixture has its own working period, after which the composition begins to lose its characteristics. Reanimate it by adding fluid and mixing will not work.
Expert advice on breeding putty
Before you dissolve the putty, you mustmake sure that the surfaces are ready, cleaned of surges, traces of plaster, dirt and greasy stains. Surfaces to be trimmed must be primed and allowed to dry. This should be done in advance, because the ready-made composition will not wait.
При разведении следует придерживаться a certain order. Prepare a clean container that has smooth walls. You will need a drill with a nozzle in the form of a whisk, as well as a dry spatula. In the tank it is necessary to pour the right amount of liquid, and then pour the dry composition, trying to direct it to the center of the tank to get a slide.
Mixing technique
If you use instructions when cookingsolution, it is necessary to determine the number of components according to the proportion. The powder should settle into the water, then you can proceed to mixing with a drill with a nozzle. If it happened that the solution did not find the desired consistency, you can add an additional amount of dry composition. To do this, it is collected with a spatula from the bag. After mixing it is necessary to repeat.
From the walls of the tank with a spatula is necessaryto collect the solution, and then immerse it in the total mass. The putty in the next step is left to swell for a few minutes. This time is necessary for the formation of molecular bonds. After a few minutes the mixture must be mixed again. If you prepare the putty composition yourself and you do not have recommendations on proportions, then it should be poured into the center of the water tank until the height of the slide is equal to one third of the height of the underwater part.
In the end, should get a solution inwhich spatula is well worth, like a spoon in sour cream. When the master collects the finished mixture, it should not fall in pieces and drain. You did everything right, if the putty slowly crawls, leaving no trace behind.
Cooking starting putty
If you have a question about how to breedstarting putty, you can use one of two ways. The first involves the use of technology similar to that used when kneading dough. This approach is relevant if there is no attachment in the form of a mixer for a drill.
For work, you need a dry container, and fitbucket. At the bottom of the bottom of the desired volume of dry composition. Water is gradually added to it. This is especially true for the plaster mix. For her, a great plastic container. Approximately 7 putty masters are poured on the bottom, then a small amount of water is added. The mixture is well mixed.
If dirt gets into the putty there is a chancethat it will harden faster than you can put it on the surface. As soon as you finish mixing, you can add the rest of the dry mixture and add liquid. Stirring is necessary to carry out until you can achieve a homogeneous putty without lumps. The second method of cooking starting putty looks the same as that described above.
Breeding finish putty
Before you dissolve the finish putty,proportions need to learn by reading the instructions. After that, you can begin to work, which will be almost no different from those that have been described for the formation of the base layer. The only difference is the need to re-mix. This is due to the fact that there should be no small lumps on the finish layer. The layer must have a thickness of not more than 1 mm, because of this, any particles will be noticeable.
Stir the mixture repeatedly andcarefully. A new portion of the putty for finishing surfaces should not be diluted in the same container where you previously prepared the previous one. The container must first be rinsed with hot water. In the same way it is necessary to do with the nozzle in the form of a mixer. Before you dissolve the liquid putty, which goes to the formation of the finishing layer, you must remove the remnants of the solution from the tool by placing them in a separate container. If it happened that the particles of the solution fell into the container with the mixture, then the volume of the material must be mixed to prevent the formation of lumps.
Preparation of the Fugenfüller finishing putty from Knauf and mixing proportions
Many novice home masters think aboutthe proportion in which to dilute the putty. If you purchased the composition for the finishing leveling, which was mentioned in the subtitle, then 1 kg of dry mix will take 0.8 liters of water.
It is important to prevent air from entering as much as possible.kneading. For this reason, mixers and other mechanical devices are not recommended. At first, the container is filled with water, only after that you can proceed to carefully pouring the dry mixture. This should be done gradually. If you immediately put the entire composition in water, then he will not have time to soak in water. After falling asleep, wait a little while the mixture is saturated with liquid. You can then begin stirring.
Conclusion
It is better to dilute the putty without a mixer, and ifdo it immediately after falling asleep composition, the mixture may lose its technical characteristics. In this case, you can deprive the layer of the main property, which is the absence of cracks after drying.
