Snow covers for roof made of metal. Mounting and fixing the snow loaders with your own hands

In winter it is very important to protect the building froman abundant thick layer of snow, which at temperatures drops then thaws, then freezes, forming a strong ice film on the surface of the roof. The layers of ice may eventually begin to fall down, so it is important to install the snow covers for the roof in a timely manner. Why are they needed and what are the features of their installation?

Main goals

Thanks to the installation of snow blocks, several problems can be solved:

1. Avoid possible damage to gutters, roofing elements.
2. Protect passers-by from the possible fall of ice and snow strata.
3. The roof will not be deformed and bend under the weight of snow, while the ceiling will be protected from water stains.
4. The decorative elements of the building and the plantation next to it will not be damaged.
5. The installation of snow-holders allows you to save time and money that may be required for reconstruction of the roof and its deformed components.
6. The main objective of these structures is to protect the roof and extend its service life.

The main thing is risk reduction

The load of snow on the roof is an indicator,Determining the thickness of the layer of snow, which affects the roofing system. Snow covers for a roof made of metal and other roofing material is a good opportunity to protect the building in a timely manner and everything that is next to it is located, from falling snow mass. Modern models of snow holders can be of several types:

• tubular;
• angled;
• lattice;
• plate-like;
• point;
• in the form of hooks.

Select the type of device you need, depending on thetype of roof and its covering, as well as climatic conditions. Install them with the use of safety devices, and if the building is above 6 m, it is necessary to arrange a fence along the perimeter of the roof.

Features of tubular and latticed snow chains

Snow-holder for metal tile and tubularLattice is a versatile tool that is ideal for mounting on a roll or sheet roof, as well as on a roof covered with natural tiles. These reliable structures can be mounted even on roofs with a large slope. It is worth remembering that if the angle of the roofing structure is 60 degrees or more, the snow load will not be taken into account. This is due to the fact that the snow cover on such a system does not last long.

The most dangerous roofing systems - with a standard slight bias. There are several reasons for this:

1. Because of the large area of ​​the roof surface of snow, a lot of it accumulates.
2. The angle of inclination in such systems is 20-35⁰, therefore, a lot of snow accumulates, and this mass also comes entirely.
3. Snow covers for a roof on such a roof will be subjected to a large static and dynamic load.

Hooks, plates and corners

These products are widely used onroofing systems, covered with roofing material or european tile. Such devices are installed during the installation of the roof or overhaul of the coating itself. The installation of snow hooks in the form of hooks is performed in several rows in a staggered manner along the entire perimeter of the roof. Fastening of products is carried out directly to the crate.

If the roof is covered with tin, metal,profiled sheeting, then you can not do without the use of plate-shaped corner snow throwers. These elements are good because they are made from the same materials as the roof itself. At the same time, installation is possible on the already completed roofing system. True, these products and defects - they do not differ in strength and durability of service.

If the roof is soft?

Because of the structural features of the structurethe equipment of a soft roof is executed a little differently. First, according to construction standards, with the arrangement of such a roofing system, the maximum angle of the ramp is not more than 15⁰. This serves as a guarantee that the roof will bealmost flat, and therefore the danger of snow convergence will be minimal. Secondly, the soft roof is characterized by a rough surface. Over the roofing material, as a rule, is placed a stone crumb, which prevents the sliding of snow. Thirdly, when installing snow covers for a soft roof, you do not need to make any changes to the design.

Features of mounting on a soft roof

Если вы заботитесь о состоянии загородного дома or office space, as well as on passers-by, which can be hit by snow avalanches, be sure to mount snow covers for the roof of metal: installation of these products is performed during roofing works or already on the finished roof. The installation process is as follows:

1. From the ledge you need to retreat about 50 cm.
2. Placement is performed in several ways: the tubulars are stacked in one line, the angled and dotted are staggered.
3. If the roof slopes are large, long, and snow falls a lot, snegozaderzhateley installed in two rows with an interval of 5-5.5 m.
4. Tubular products are fastened to the crate by means of screws, which reduces the load on the roof.
5. Fasteners should be removed from each other by 60-110 cm, and all holes must necessarily be hermetically sealed.

How to be with metal?

Снегозадержатели для крыши из металлочерепицы play an important role, especially if the climatic conditions of the region involve permanent and severe snowfalls. To perform installation of devices on the roof of metal, you need to perform a number of works:

1. First, the right kind of supports is selected,the distance between them is calculated. It is important to take into account both the force load, and the type of roof, and the type of the crate, and the diameter of the rail. The expected load depends on the material and the method of its attachment.
2. For a long roof and steep slope, the supports should be placed in several rows, evenly distributed along the entire length.
3. If snow covers for a roof made of high-quality metal, they do not need to be treated with an additional coating.
4. Before installing additional roof elements, you need to check the locations of future anchorages for strength.
5. Installation of snow traps is carried out above the external bearing wall near the roof cornice.

Mounting snegozaderzhateley best to think about at the design stage of the roofing system.

What to choose?

Снегозадержатели для крыши из металлочерепицы и Other roofing materials are presented in a wide variety. They are different in construction and are designed for different roofing. The simplest and most effective option is to give preference to lattice snow holders, which will cope with even small pieces of ice. These products are great for installation on country houses, tiled. The cheapest option is plate-like snow traps, which can be mounted on the roof with metal roofing. They are well suited for this material both in composition and in external characteristics. True, they do not provide reliable protection, and require a certain angle of skates - not more than 30⁰.

When tubular snow holders are installedfor a roof made of metal, fixing is performed above the supporting wall, parallel to the edge of the ramp with the use of screws, screws. But for a soft roof, it's best to use point (or tubular) products that will enhance safety and improve the protection of gutters.

If the installation of tubular structures is performed, the following should be considered:

1. It will take a standard crate step 350 mm (for metal) and 400 mm (for corrugated board).
2. Installation is carried out by means of a special universal bracket.
3. Most often the product is supplied with plastic seals, which allow to achieve a high degree of tightness and prevent the appearance of leaks.

Brand BORGE: what's special?

Representatives of the company pay maximum attention toThat the houses were comfortable, safe and comfortable for living. And for this you need to try to do everything possible to reach these parameters. Snow covers for the roof of metal Borge create a reliable safety system of high quality. The company's products consist of the following products:

1. Snegozaderzhateley for metal, profiled, soft roof.
2. Products for rebated roofs are put according to the principle without holes on the roof.
3. Standard snegozaderzhateli assume a flooring on special hooks and roofing coverings with a high profile.

Benefits of Borge

First, it speaks productively of the highstrength of products. Snow covers are created on the basis of flat-oval pipes, the thickness of the walls is 1 mm. Secondly, the products are reliable because the brackets have sufficient thickness and do not bend, even if the lateral load is strong. Thirdly, the installation of snegozaderzhateley carried out so that the integrity of the coating and its durability. Fourthly, all components of snow holders are of high quality, because they are powder coated, the color of which can be selected. Fifthly, the company provides a guarantee for its products for 25 years!

Snow covers for the roof made of metal (photo shows how simple and convenient their design) Borge are designed for a certain coating.