Washing machine, just like any otherhousehold appliances, sometimes can fail. The problem may arise with the set or discharge of water, with the quality of the spin, and sometimes it happens that the washing machine drum does not spin at all. And after the launch of the program, the machine can regularly be filled with water, but it will not go further. The reasons for the fact that the drum does not spin in the machine can be several, and the first thing to do is to understand which one of them takes place.
Excess weight
First of all, you need to exclude the simplest:the machine may not spin the drum because it is overloaded. Modern washing machines are equipped with appropriate sensors, and if the weight of the laundry is exceeded, it will not be washed. In this case, you must turn off the machine, unload some of the laundry and try to start the program again. If the problem persists, then everything is not so simple, and we will have to look further.
The problem with the drive belt
Then you should release the machine fromlinen, drain, of course, before the water from the tank, de-energize the unit and try to spin the drum by hand. All hostesses manually scroll the drum in search of the remaining laundry at the end of the wash and remember how it spins in its normal state. So, if it does not rotate as usual, but is clearly lighter, without any resistance, then the problem is with the drum drive belt. In that case, of course, if he is there. There is no such detail in direct drive washing machines.
To see the belt itself and check whatIt happened to him, it is necessary to dismantle the back wall of the washing machine. The belt could slip and tear. In the first case, putting it in place will not be difficult. The torn part will have to be replaced. The belt usually shows its characteristics: the length, as well as the number and height of the wedges. According to this information, you need to look for a replacement. And so that such a problem does not arise again, you should avoid overloading the machine and the imbalance of the laundry in the drum. This is what leads to stretching, slipping and breaking the belt.
The drum is jammed with a foreign object.
If the belt is intact and is on its rightfulplace, however, the washing machine drum is spinning tightly, with a screech, or does not rotate at all, that is, there is a possibility that there is some foreign object between the drum and the tank that got there through the rubber cuff, which stalled the drum. You can get it through the hole intended for the electric heating element or heating element. The heating element is usually located under the tank, and you can usually reach it from behind. It is not difficult to remove it, and through the hole formed, you can try to get something that the washing machine drum does not spin - a coin or a key, for example, or some small piece of clothing, such as a baby sock. If the operation is successful, the heating element is installed in its original place, small items of clothing are subsequently washed in a special bag, and the pockets are carefully checked before the laundry is placed in the car.
Faulty TEN
By the way, the burned out heating element toomay be the reason that the washing machine will refuse to work. The drum does not spin because no water is heated to the required temperature, and the command to start the motor is not given. The extracted TEH is tested, and if it is still burned out, it is replaced. In order for the heating element to serve for a long time, it is necessary to use water softening agents to prevent scaling on it.
Bearing wear
Do not spin the washing machine drum and thenwhen the bearings have seized due to wear. Perhaps due to the use of too aggressive detergents, the gland began to pass water, and the constant humid environment in which the bearings had to be found led to their corrosion and gradual destruction. In this case, the washing machine drum turns badly by hand. To replace the bearings, you need almost complete disassembly of the device. Therefore, such a procedure as the replacement of bearings is recommended to be done only by specialists with relevant experience and knowledge.
Electric motor
В данном случае проблема может быть в изношенных graphite brushes engine. If they are worn out so that they no longer come into contact with the collector and do not create the desired electromagnetic field, so that the engine does not start, then they can only be replaced with new ones. Perhaps the case is in the engine itself, and there was a closure or breakage of its winding. This rarely happens, but, given the instability of the voltage in the domestic network, it is quite possible. Or maybe leaks are to blame. There is no way to do without diagnostics in the workshop - this is a serious and costly breakdown.
Faulty electronic module
This detail is all head to modern householddevices. And if the "brain" does not give the appropriate command, then, therefore, the drum of the washing machine is not spinning. The electronic board must either be reflashed or replaced. Due to the specificity of this task, an unprepared user of the washing machine will not cope with this.
Other reasons
Modern washing machines refuseturn on even with such trifles, it would seem, as a blockage in the drain filter. So if you have any problems with the stable operation of the home appliance, it is not superfluous to check the filter. The instruction manual for the instrument usually describes in detail the procedure for its removal and cleaning. Usually it is located on the front panel, and you can reach it by removing the small cover at the very bottom of the case. Next you need to unscrew the filter. This will result in some amount of water, so it is necessary to provide for either a flat container or a few thick rags in order not to collect water throughout the room. In the filter, you can find a lot of interesting things: buttons, coins, pile, hair, husk - in general, you never know what can get into the washing machine with the laundry. Preventive cleaning of the filter is necessary from time to time.
Failure of the wiring inside the machine is also the cause of standing still drum, since the voltage on the engine simply will not be applied.
In older models of washing machines, the starting capacitor may fail and the engine will not turn on. This item must be replaced.
conclusions
So, the failure of the drum washing machine spinThere may be various reasons: mechanical seizure or a broken belt, which can be easily fixed by yourself, or an electronics failure or a device engine failure. The last two tasks can hardly be done by a person who does not have adequate experience in repairing washing machines. Specialists in the workshop are able to solve such problems much faster and more efficiently.
