Concrete mortar unit is an installation formaking concrete. If you make a comparison with the plant, the difference will be in the configuration. However, with the help of this equipment it is possible to manufacture all brands of concrete. At the same time for the operation of some installations there is no need for a person to participate in the process. Some equipment options require multiple recipes.
By picking such devices can bemobile or stationary. The latter version is considered to be classic, it is characterized by high productivity and work efficiency. Typically, such facilities are used in conditions of enterprises that are engaged in long-term work in one place.
Description
Mobile concrete plant allows you to makeconcrete in medium quantities. Such plants are highly efficient and are usually used by specialists of construction and commercial organizations who work in different or remote places. Mortar units can also be classified according to their characteristics; however, they are similar in function. You can be sure of this by reading the comparison of some models.
Different installations have their own technical features. For example, consider the model "BRUN BRUS-15G", which consists of:
- dispenser of cement, liquid additives and water;
- concrete mixer with remote control;
- skip lift;
- conveyor;
- dispenser;
- bunker;
- vibrating feeder;
- grab with a remote control.
This installation can work under controlautomatic or manual mode. The operator of the concrete-mortar unit of this type is able to cope with the installation on their own or with the help of another person. The equipment can be operated in regions with different climatic conditions, and the temperature can drop to -300 ° C.
Technical characteristics BSU-10/17
Among the characteristics of the described nodes should be highlighted:
- performance;
- installed power;
- the number of aggregate fractions;
- storage capacity of aggregates;
- cement storage tanks;
- capacity for loading and exiting;
- heating system at low temperatures;
- type of mixer.
Concrete and mortar installation can have a performance ranging from 15 to 20 m3 /h, in winter, this figure can be reduced to 10 m3 /h. The capacity of the warehouse of aggregates and cement are 200 m3 and 40 tons respectively.If we are talking about the capacity for loading and exiting, then these parameters are 750 and 500, respectively. A steam installation is used as a heating system. Power equipment is 40 kW, while the mass is 37,200 kg.
Technical characteristics of the node BRUS-15G
As an example, you may consider another BRU. Concrete mortar unit, which was mentioned above, has a capacity of 15 m3 /h. The number of aggregate fractions reaches 3 pieces, while the cement warehouse is 24 m3. The equipment weighs 12 tons, and its installed capacity is 36 kW.
Characteristics of the installation BRU UBRS-10
If you decide to choose a mobile concrete plant, then it is worth considering the model “BRU UBRS-10", whose performance is 24 m3 /This equipment uses a concrete mixer SB-146A, and the dispenser includes:
- water flow sensor;
- cement doser with sensor and control controller;
- inert materials dispenser with controller.
Considering the concrete-mortar unit, you should also take an interest in the capacity of the open storage of aggregates, which is 200 m.3. As for the capacity of the cement warehouse, it reaches 40 m3, but the capacity of the supply tank for chemical additives is equivalent to 1.5 m3. The water in the supply tank can hold 3.5 m3. The dosing system in this installation is electronic-mechanical, while the ratio of mortar to concrete mixes is as follows: 0.65 / 0, 5.
For this equipment the level of vapor pressureis 68.6 kPa, with regard to the working pressure of the pneumatic executive system, it can vary from 0.39 to 0.49 MPa. Gas or diesel fuel can be used as fuel, and consumption is 102 g / kg of steam.
Characteristics of the solution of a concrete node of the brand FIBO INTERCON M2200
If you decide to purchase the article describedequipment, it is worth considering a concrete-concrete node of a foreign manufacturer. The model was mentioned above. It is based on a three-axle trailer with a front axle and sectional hoppers for aggregates. As the last can act rubble or sand.
For its power class, this equipment acts as the most compact unit in the world. Equipment assumes the presence of:
- water tank mixer;
- pump conveyor for chemical additives;
- high pressure cleaner with automatic control.
The volume of the mixer can vary from 1,500 to 2,200 liters, while 500 liters can be placed in a water tank. An additional feature is the option of heating and dosage system.
The pump has volumetric dosing, cleaneroperates at a pressure of 160 kW. It will be quite simple to operate this concrete-mortar unit, because it has automatic control on 25 recipes with calculation of loadings, time tolerance and control of dosing. The sand can be adjusted manually for sand. The download protocol is displayed in the production diary, and protocols and invoices are printed if necessary. The discharge height is 1120 mm.
Conclusion
Modern mobile concrete plants andConcrete mortar units are used in production quite often. They allow you to get a large amount of the mixture, which would be difficult to achieve when working manually. Installations usually have a steel frame that provides ease of transport and has suitable fixings for winter trim. Additional benefits are equipment in the form of tanks, mixers and pumps. Management is carried out automatically, which almost completely eliminates human intervention.
