Many people are interested in the answer to the question about how to wipe the mounting foam. And this is what we will try to tell in this review.
Foam precursors
Mounting foam appeared in the construction sectorrecently. Previously, before its appearance, cement and tow were used. This solution was bred long enough. To all other works also did not differ simplicity and speed.
Currently, the mounting foam is usedalmost everywhere. And not only in construction, but also in repair. Surely many of you have seen a substance sticking out of the cracks, which is similar to a foam plastic. This is the mounting foam.
Main advantages of the material
The main advantage of this material is considered to beease of use, as there is no need for additional work. In addition, you do not need to purchase and use a wide variety of mechanical devices. All that is needed is the material itself. The mounting foam is realized in specialized cylinders that do not differ too much in volume. Inside the tank, besides the foam itself, there is a gas that displaces it. Select the mounting foam carefully. Some not completely conscientious producers can add any harmful substances to health.
Be careful
Working with a mounting foam, it is necessary to exerciseneatness, because the material is different in tenacity and durability. In the event that avoiding the hit did not work, you need to get rid of the foam marks as soon as possible. How to wipe the mounting foam? To begin with, the place that was stained should be thoroughly wiped with a rag, not smearing, and removing the material. Then you need to find the means by which you can remove the foam. For example, acetone or gasoline.
Than wipe the mounting foam, if these materialsat hand is not? You can prepare a special solution. To do this, dilute the salt in the water, and then rub the place where the foam hit, using a pumice stone or a brush. It must be remembered that working with this kind of material should be neat. And if you remove the foam from the skin, you can get rid of her traces from the hair much harder. And just cut the curl with traces of material - the only option available in this case.
How to wipe the mounting foam? What can be used to get rid of traces of building material?
В той ситуации, если пена уже полностью засохла on the surface of the skin, then the solvents will not help. In such a situation, you can get rid of the traces of material only mechanically. This is also stated in the instructions for use by foam manufacturers. How to wipe the mounting foam from your hands in this situation? It is necessary to grease them with a fat cream in the most careful way. This is necessary in order to reduce the impact of aggressive material during cleaning. After this, you must take a hard brush, apply soap on it and begin to rub the surface of the skin from the foam.
What can wipe out the foam in the situationif this technique is not very helpful? Instead of a brush, you can use pumice stone and soft sandpaper. In order to get rid of the hardened substance as quickly as possible, it is necessary to hold hands in hot water for ten minutes before the cleaning procedure. This must be done to steam out the skin as it should.
If after a mechanical cleaning method on the handsthere are still traces of foam, you can try to get rid of them through nails. The procedure for removing foam, which has already managed to dry, is quite time-consuming and complicated. It may take about an hour.
In any method of all of the above, it should be noted that the skin should be well processed with a rich cream. You can also make an oil bath.
How to get rid of traces of foam from things?
How to wipe the foam from clothes?As soon as traces of foam were seen on the clothes, immediately take a thinner with a rag and begin to scrub this substance. If you do not have time to get rid of traces of foam in time, you will not save clothes with anything, since the frozen material will not be amenable to washing or cleaning. However, the solvent can spoil the clothes. To do this, just check the reaction by applying a cotton swab on the back of the thing.
For cleaning clothes can also be purchased.special remedy. However, you must first familiarize yourself with its composition and instructions for use. Otherwise, only the probability of damage to things will increase. The negative point characteristic of specialized cleaners is the presence of a large amount of acetone in the composition. This must be taken into account if there is a thing that is not resistant to the effects of this type of solvent.
Sometimes, to get rid of traces of foamwith clothes, it is enough just to use vegetable oil. The same can be said if the question arose about how to wipe the mounting foam from a plastic window or linoleum. To do this, a piece of material is cut from clothes so that only a minimal amount of foam is left on things. Then it is required to apply oil on the polluted surface and hold it for half an hour. After this, the foam will be removed quickly and easily.
Conclusion
In this review, we gave several examples that tell how to remove foam from leather or clothing. We hope that one of these methods will help you cope with this task.
