Motoblock - an indispensable assistant for the ownerprivate suburban housing. The presence of such equipment makes it easier to clean the infield, processing the land in the country and in front of the house. However, with the onset of cold weather does not necessarily send a manual tractor for storage. Instead, you can install a snow plow on the motor-block, which will allow cleaning the home territory from snow and ice.
Principle of operation
Buying the most functional snowploweron the motoblock, the user, as a rule, has the opportunity to adjust the angle and range of snow scatter during cleaning of the site. At the same time, there are fairly simple designs in the form of brushes and ordinary buckets, which will be discussed in more detail below.
Shovel-blade
The width of the blade varies from 80 to 150 cm.Therefore, the user has the opportunity to choose exactly the design, the dimensions of which correspond to the type and power of the existing motoblock. For the lightest hand-held tractors, buckets with a width of no more than a meter are designed. Really powerful motoblocks can be equipped with heavy-weight designs of maximum width.
The edges of the shovel-blade contain a rubber coating,which protects the surface from damage during snow cleaning. Such snowplows allow you to adjust the angle of rotation and tilt of the bucket. As a result, the user has the opportunity to expose the blade in the optimal position when performing certain work on the backyard or suburban area.
Snow blower with a brush
The snow-picker with a brush is attached to the rotating shaft of the motor block. During one pass, a technician equipped with such a device is able to clean the track more than one meter wide.
При эксплуатации снегоуборщика со щеткой имеется The ability to adjust the grip of the snow cap in several directions, due to the displacement of the structure forward, to the right or to the left. The stripping height is also adjustable.
Rotary snow blower
The main structural element of such a nozzleAuger appears that contains paddle wheels. The rotating device captures the snow cap, which moves upwards, passes through the bell and is thrown out beyond the cleared area.
Snowplower for motoblock "Salute"
Snowplow is a prefabricated weldedconstruction. The main functional element is a screw auger. During its rotation, the snow mass moves in a direction from the edges to the center. Movable blades of the device ensure the advance of snow to the nozzle. The direction of ejection is regulated by the rotary screen. On both sides of the body there are support plates, by means of which the height of snow removal is corrected.
Snowplow characteristics:
- length - 60 cm;
- height - 82 cm;
- width - 64 cm;
- grip - 50 cm;
- the possibility of harvesting a snow cap with a thickness of up to 17 cm;
- frequency of revolutions of the screw to 2100 rotations per minute;
- the weight of the snow-picker is 60 kg.
Snow-picker for the Neva motor-block
What characteristics does the snowplower have on"The Neva"? Motoblock, equipped with such attachments, allows you to capture a snow mass of 60 cm wide and about 50 cm high. As a result, it becomes possible to effectively use the device not only when cleaning the infield area, but also cleaning up from replacing impressive production areas.
Snow-picker for motoblock "Neva" needscareful care and timely maintenance. To extend the life of the device, before every start of work it is necessary to check the reliability of the fasteners, the quality of the belt and bolted connections. Fastening of fasteners is required after every 5-6 hours of continuous operation.
Snow thrower for motoblock own hands
To assemble a self-made snowplower tomotoblock, it is enough to get a powerful engine that can be extracted from an old hand-held tractor. As a basis for the manufacture of auger of the future device, roofing sheet metal is suitable. Sidewall can be made of plywood with a thickness of 10 mm.
For welding frame construction of self-madesnowplower enough to take a metal corner. The handle will serve as a tube half an inch in diameter. From the ¾-inch pipe, it is possible to make a screw shaft, in the middle of which to create a saw for fastening metal blades intended for ejecting snow.
To prepare the auger from the roofing material, an electric jigsaw needs to cut the conveyor belt in the form of four rings. The diameter of each of them should be about 30 cm.
The engine is mounted on a platform thatconnects to the snowthrower bucket with welded corners. A belt joint can serve as a gear that will transmit torque to the auger shaft.
The design is most convenient to put on skis,as the wheels will often get stuck in snowy notes. This, in turn, will create a whole lot of inconvenience in the process of operating a homemade snowthrower.
For the manufacture of rotary chute throughsnow mass will be thrown out; it is enough to take a plastic sewer pipe of impressive diameter. The latter is fixed on the body of the screw. In the end, it remains only to give a snow blower a presentable look, having treated the surface with paint.
Eventually
