A lot of people in the construction and repair workused welding semi-automatic "Aurora Overman 180". Feedback on this unit is mostly positive. And the mode of operation of the device allows you to use it as long as possible, and for both professional and everyday tasks.
Features of using the tool
The AuroraPro Overman 180 inverter is used in MIG-MAG shielding gas for semi-automatic welding. Areas of use of the apparatus are as follows:
- production;
- construction - professional and amateur;
- car service and garages.
Management and benefits
The welding inverter semi-automatic “Aurora Overman 180” is controlled with the help of special parameters located on the front panel. Thanks to them, you can customize it in the proper way.
The key advantage of the device is that withit can be boiled in networks where large voltage drops occur. Aurora Pro Overman 180 is able to successfully perform tasks, even if the voltage drops to 140 volts.
What can the unit?
On the Internet, people very well appreciate the welding semi-automatic "Aurora Overman 180". Reviews say that it can perform a large number of tasks. For example:
- sheet metal welding;
- metal structures with long seams;
- bodywork;
- welding carbon and stainless steel, aluminum and other non-ferrous metals.
Device design
Tool Aurora Pro Overman 180 has a smoothadjustment of inductance, current and welding voltage. This allows you to make an easy setting before work. You can adjust parameters such as penetration depth, the shape of the roller and the rigidity of the arc. This all affects the quality of work of such a device as a semi-automatic welding machine.
Wire feed is also adjustable from slowup fast. And the high stability of arc burning and the reduction of splashing make it possible to increase the level of instrument safety. It also improves the quality of welding and reduces the consumption of wire - filler material.
This model involved a modern MOSFET inverter technology. It works thanks to TOSHIBA brand transistors, this allows you to increase the efficiency of the device by more than 80 percent.
Terms of Use
In what conditions and how can you applywelding semiautomatic Aurora Overman 180? Customer reviews indicate that they can operate in a normal environment at temperatures ranging from 10 degrees below zero to 40 degrees of heat. Relative humidity should be a maximum of 80 percent. And in an argon environment can be used in conditions of + 1-2 percent oxygen.
- The device must be grounded by a conductor connected to a special terminal on its rear panel;
- Before turning on, do not forget to check the compliance of the frequency of the current and voltage with the parameters of your unit;
- you need to periodically clean it from dirt and dust,which accumulate from the inside. This is done with the help of compressed air, the jet of which should not be directed at the electrical components of the device so that they will not break;
- после окончания работы в случае если аппарат for some time was in conditions of low temperature (5 degrees or below), then it should not be included for at least 2 hours after carrying to a warmer place. This causes condensation to form;
- The semiautomatic device is used only in protective gloves, shoes, clothes and a mask.
Specifications
The device "Aurora Pro Overman 180" has dimensionsequal to 482 to 197 to 466 mm. Its power is 5.2 kW. The welding current index is from 40 to 175 A. It has an air cooling method. Possible types of welding are:
- MIG;
- MAG;
- without gas.
Other indicators
The welding machine Aurora Pro Overman 180 has an internal coil arrangement. The minimum metal thickness is 0.60 mm, and the wire is fed at a speed of 2 to 15 meters per minute.
The efficiency of the unit is 80 percent, the degree of protection is IP21, and an insulation class such as F is also assigned to it.
Low weight and compact dimensions allow withoutlabor to move the device from place to place and work even in small spaces. The recommended voltage is 220 V, you can connect it to a normal network.
The welding machine can work with thick and thin metals. And thanks to the optimal diameter of the wire without gas, you can make seams that are different from each other in depth and width.
Completion and cost
The device consists of the following components:
- one burner for three meters;
- three-meter cable 25 mm;
- one clip to 300A.
Features of the structure
On the welding machine of this brand, the control panel is equipped with levers for adjusting such parameters as:
- welding current;
- inductance;
- voltage;
- wire feed speed switch;
- working condition of the tool.
A universal connector helps in case of need to change the burner.
How wire is fed into the device
When you are doing welding, it’s importantThe criterion of successful work is the availability of reliable and high-quality mechanisms that feed the wire. Their key advantage is that they facilitate your actions. After all, the wire is fed directly to the welding destination.
Previously used for this push orpulling device, but now use a multifunctional device, equipped with an electronic control system. Control of operating parameters greatly simplifies welding.
There are three types of such devices, which differ depending on the method of wire drawing:
- Devices push action mostare common. Do not make the torch heavier and facilitate the welding process. They must be installed next to the apparatus and through the special guide channel to draw the wire, so it will reach the tip.
- Pulling action - this mechanism is goinginside the device in the burner housing and delivers the material to itself. Thanks to him, you can work if you need it with sleeves of increased length. But this device makes the torch heavier, which slows down its action.
- Combined - combine the properties of the previous two mechanisms. There are very rare.
In these mechanisms, schemes consisting of 2 and 4 rollers are used, it all depends on the wire diameter. For maximum use double. It includes pinch and drive rollers.
The wire moves due to pressure between the rollers. Its diameter should be less than in the channel. If it is larger, the mechanism will not ensure stable movement.
What customers say
And what opinion did customers have about the semi-automatic welding machine Aurora Overman 180? Reviews on the Internet about him are mostly positive. On their basis, we can highlight the following advantages of the tool:
- build quality;
- the presence of sensitive settings;
- excellent mechanics;
- wide range of applications.
From the shortcomings commentators highlight the high cost of the apparatus. But, in their opinion, for such a quality it is fully justified.
This semi-automatic has a justified costaccording to some people, after him, I no longer want to use less expensive tools, and the quality and the result of the work done exceeds all possible expectations. Sometimes it's better to try it yourself than to hear or reread a lot of reviews. After all, everyone, as you know, has an opinion on everything.
