How to build a fence with brick pillars?

To the arrangement of fences on the backyardshould be treated responsibly. After all, the designs of this assignment perform not only a protective, but also aesthetic function. Currently, homeowners are increasingly installing a fence with brick pillars. Let's find out how to cope with this task without the help of specialists.

Foundation for a fence with brick pillars

Under the fencing of this kind, you can lay both a tape and columnar foundation. For laying the foundation for a fence with brick poles you will need the following materials:

• crushed stone;
• cement;
• a rock;
• sand;
• metal fittings.

For laying the strip foundationdig a pit, the width of which corresponds to the width of the spans of the future fence. Further in the trench the metal reinforcement is mounted. Finally, fill the grout in one step. In this case, the depth of the composition should not exceed 50 cm from the surface of the soil. Otherwise, brick poles may not be stable enough.

As for the columnar foundation, its fillingproduce exclusively on sustainable soil. For its laying, drill holes directly in the proposed locations of the support of the future fence to the depth of freezing of the ground. A vertical pipe is installed in the center of the columnar pit. The latter plays the role of the foundation of a brick pillar. To make the construction as strong as possible, experts advise placing a metal reinforcement in the pipe, which is poured with concrete. Then the prepared pole is fixed with supports and left in this position for several days before the final hardening of the concrete.

Tools for building a fence

To build a fence (with brick pillars, of course) of sheet material, you will need the following tools:

• shovel and bayonet shovel;
• building level;
• a nylon thread;
• yardstick;
• hammer;
• perforator;
• Screwdrivers, screwdrivers;
• a set of drills for metal;
• concrete mixer;
• paint brushes;
• welding machine.

Installation of brick poles

For the erection of brick poles for installationA cement-sand mixture with a ratio of these components of 1: 3 is required. Before the masonry is started, the foundation is waterproofed in the areas where the supports will later be located. For this it is sufficient to use a roofing material or other available material.

Before the end of the working day it is recommended to lay out a brick pillar completely. Only in this case the structure will be stable and will be able to withstand the maximum loads.

In conclusion, a brick pillar under the fencecovered with a decorative cover. The latter can be made of sheet steel, cast from concrete or cut out of galvanizing. If you plan to install on the ends of the pillars of factory-made covers, it is advisable to give preference to products painted with pigment compounds that do not "cloud" after the first rain.

Installation of frame under the fence

To make a profiled fence with brickpoles, the preparation of the frame is required. The latter is formed from steel reinforcement by arc welding. The main task here is a strong connection of metal bridges with pre-installed in the foundation of vertical pipes, which are the basis of future brick pillars. For this purpose, one steel profile is welded at the bottom of the column, the other at the top.

Further, using a masonry solution of mediumplasticity is the installation of the facing brick. Upon completion of the formation of the poles, they proceed to the installation of corrugated sheets. Two such masters are quite capable of coping with this work.

How to build a fence of corrugated board with brick poles?

Picking up material for the construction of the fence,give preference to products with an anti-corrosion coating or a layer of galvanizing. To prevent damage to the edges of corrugated sheets allows the overlay on the foundation of the cardboard.

To make a fence with brick pillars, inThe quality of fasteners for joining the fence planes is using self-tapping screws with a size of 30 mm. In the course of work, an electric drill or a screwdriver is used. And these instruments should support the mode of operation at low revs.

The sheets of corrugated sheets are superimposed on each other with overlapping into a single wave. Then fasteners are fixed in the junction points. The places of material damage by screws are painted over with alkyd paint.

Finally

Fence ribbon with brick pillars ofProfiled sheeting length of about 15 meters are built approximately for 2 weeks. Lay sheets of material quite realistically. Help specialist may be needed only when constructing directly brick pillars.