Broken tire, shock absorber repair, brakes orThe muffler makes many drivers wonder how to remove the rear wheel on a scooter. Make it harder than it seems at first glance. Although the second wheel is mounted on just one nut, this operation may require special skills and knowledge.
Reasons for removing the rear wheel
A scooter, like any other vehicle,subject to the laws of physics. Parts wear out and need repair. No exception are the wheels of the vehicle. At first glance, removing the rear wheel from a moped is easy. Yes, and it keeps only one nut. But this is a deceptive impression. In order to get to the rear wheel rim, the owner will have to sweat a lot, removing most of the plastic and parts.
Reasons for removing the rear wheel from a scooter canbe the most diverse. Most often it is a flat tire, because few motorcycle enthusiasts have ever ridden a sharp object with a wheel. But in the back of the scooter, in addition, there are many important details, access to which will require dismantling half of the vehicle. And what else can be the cause of repair with the dismantling of the rear wheel? We list:
- Bad brake pads. Brakes are the most important part of a motorcycle. If they work poorly, you need to troubleshoot as soon as possible.
- Replacing the old wheel with a new one.
- Wheel balancing
- Replacing the shaft of the gearbox.
- Paint disc.
- Tuning drum brakes.
- Replacing a worn or punctured wheel.
Tools for work
Before removing the rear wheel on a scooter (150 cm ³), you need to find tools that you can’t do without repairs. You will need:
- socket wrench;
- clean rag;
- wooden bar.
A little luck and patience will help you complete the job quickly.
Rear Wheel Removal Instructions
How to remove the rear wheel from a scooter? The quicker step-by-step instructions suggested below will help you to understand this:
- Position the scooter so that the rear wheel spins in the air.
- Remove the silencer. To do this, remove the seat and plastic, and then unscrew the nuts that hold the muffler. It is important not to take them out completely, but only to loosen them.
- Use a socket wrench to loosen the nuts securing the muffler to the cylinder. Remove it from the scooter. In this case, paranitic gasket may be lost, so be careful.
- If the muffler is dirty, it can be cleaned fromsoot and dirt. To do this, heat the outside with a blowtorch, and inside go with a stiff metal brush. After all the manipulations, it is better to cover the exhaust hole of the muffler with a clean cloth so that no foreign particles get into it.
- Most mopeds have a mono damper. In case there are two of them in your model, and they are located in the rear part, you need to unscrew the nuts and dismantle them.
- If you have a rear disc brake, you need to do the same: carefully unscrew the brake caliper and move it to the side.
- And now you can proceed directly toremoving the wheel. Unscrew the carrier nut with the impact wrench. If this is not at hand, the usual screwdriver will do. But in this case it is recommended to fix the wheel using a wooden beam.
- Remove the wheel from the slot.
To install the wheel, perform all the above steps in reverse order.
Repair scooter "Honda"
Японский скутер Honda уже давно держится в тройке best-selling vehicles with engine sizes up to 150 cm³. Modern design, thoughtful and comfortable seat, maneuverable chassis, engine with economical fuel consumption make Honda the darling of many.
К несомненным плюсам скутера можно отнести и liquid cooling system, and V-shaped transmission, and 4-stroke engine with one cylinder. The Honda mopeds consume about 2.5 liters per 100 km, and the speed can reach up to 100 km / h.
When driving off-road moped owners oftenHit sharp objects that can damage tires. But removing the rear wheel on a Honda scooter is not easy because of the burning attached to the splines, which glues the parts together and makes disassembly difficult. In this case, experienced scooter drivers advise sprinkling with WD-40, and then gently tapping the wheel closer to the center through a piece of wood.
Troubleshooting the scooter "Racer"
The company Racer entered the world market recently.Nevertheless, its products have already attracted motorists. A distinctive feature of this scooter is a kick-starter, which allows you to start it even when the battery is seated. Fuel consumption per 100 km ranges from 2 to 5 liters. The 4-stroke engine has an electronic injection system and can reach speeds of up to 80 km / h.
When repairing the wheels make it difficult to remove them twodrum brakes installed at the back and front. Therefore, the question of how to remove the rear wheel on the scooter "Racer" is very relevant. To do this, you need to do the actions described in the chapter "Instructions", but with one amendment. Before removing the wheel itself, the brake cable that “sits” on the pads should be loosened. After that, the procedure should go through without too much difficulty.
How to remove the rear wheel on the scooter "Irbis"
Another brand of scooters with engine capacity up to 150cm³ - Irbis. The products of this brand has a brutal design, two powerful front headlights and bright colors. Seeing such a scooter on the road, you will not confuse it with anything. The largest cubic meter models can reach speeds of up to 90 km / h. Disc brakes quickly stop it in case of extreme braking. Oil cooling prevents the motor from overheating.
Усиленная подвеска с двумя амортизаторами может deliver a lot of problems when removing the rear wheel. To access the tire, you first have to unscrew the muffler, and then the rear brake. On the "Irbis" scooters install monoamortizator, therefore, in this part of the problems should arise.
Recommendations from the mechanics
You can meet many recommendations anddiscussions on how to remove the rear wheel on a scooter. Experienced motorists recommend using WD-40 penetrating lubricant (or gasoline in case of emergency) to make repairs easier, and thoroughly clean any dirt and degrease before installing the parts. It is also strongly advised to grease the splines with grease. After installing the nut, it is recommended to tighten it tightly, jerking, but without impacts. To keep the wheel in place instead of a bar, you can use a variator cover, which will not allow it to turn.
As a last resort, if you faildismantle the wheel yourself, experts recommend contacting the nearest proven service. The same should be done if, after removing the parts, you found serious damage to one of them.
Outcomes
Every scooter occasionally needsrepair. Faulty operation of the vehicle not only interferes with comfortable driving, but also endangers the life of its driver. Repairing a scooter with your own hands is easy enough if you sit down before this and properly understand the details. Sometimes the process can stall on some element, then it is recommended to carefully follow the entire sequence of steps from the very beginning - perhaps somewhere a mistake was made. When replacing the rear wheel you need to take the time and be careful, and then you will succeed.
Successes in repair and good luck on the roads!
